2.3 Turbo manual available for Bellevue and Sturgis

[Patrick]

The Complete Turbo 2.3L EEC-IV Handbook

3rd edition now includes a 11x 17 foldout page of the ECA operating modes and the sensors and actuators. There is also a new table of ECA control algorithms and sensors and actuators. Additionally there is some information about "FMEM".

3964

The 2nd edition added a 11x17 page of all the pinouts on the ECA's used on the 2.3L turbo FORDS. This page has a table of pinouts, pin application, signal name, and test spec and definition.
This book covers the EEC -IV (Electronic Engine Control, type 4) installed on turbocharged FORDs. It's purpose is to: educate the reader, assist in troubleshooting problems, and provide information to allow the reader to perform modifications (not for street use, of course). There are 7 chapters: component locator, fuel injection components, EEC pin out, EEC self tests, other engine components, glossary, and bibligraphy.

The two sections on components cover all the components that make up the EEC-IV. The sections on ECC pin-out, and self-test are set up specifically for testing and diagnosing the EEC-IV system. The EFI component section has engineering data for most components. The section on other components covers performance aspects of the turbo, intercooler, and gasoline. Finally, the bibliography covers the reference material that was used to assemble this book.

The book is 8 1/2 x 11 with plastic covers and plastic 'comb' binding. The book is designed for long life under the hood and on the bench.

"It's extremely clear, concise and well-organized information makes it an essential addition to the XR4ti, SVO, or Turbo Coupe owner's tuneup and diagnostic toolbox.":Roland Zuk

"Nowhere else before, was all this information available in one place, at such a reasonable cost, and in plain language that's understandable.": Dave Compton

Price (plus shipping): $20 (Editor's note: Need to calculate shipping costs for mail orders)

Save shipping charges and pre-order for delivery at Knott's CA, Bellevue WA, or Sturgis Mustang Rally SD events in 2013.

3965

(PM Meotchh , our treasurer paypal request for payment here)

[SVOJR]

If I would of known I would of taken one of these from you Patrick.

[Meotchh]

Jr, the books are still available. Let me know if you still want one & I will pm you with the total with shipping.

[Patrick]

Jr, the books are still available. Let me know if you still want one & I will pm you with the total with shipping.
The 2.3 Turbo book from Fleming is available too, for $15. It would probably fit in the same $5.60 USPS shipping package.

[SVOC]

Mitch/Pat would you calculate a total for BOTH books going to 78602

Thanks, Jeff

[Meotchh]

Jeff,
I just sent you a PM

[SVOC]

Thanks Mitch :)

[SVOC]

Thanks ;)

https://fbcdn-sphotos-f-a.akamaihd.net/hphotos-ak-ash3/1017228_10152939128480529_1191444159_n.jpg

[Meotchh]

No problem Jeff, glad you got em. Quantities of Alan Slocom' s book are running dry. I'm down to the last two copies. It might be several months before we get more.

[Laredo]

Will there be more available for Sturgis? I would like to get a copy also.

[Jack B]

Are there any left? I would like a copy if you can mail one.

thanks,
jack

[Meotchh]

Jack,
We are waiting for more copies of Alan Slocum's book. We'll post an update when we have more in stock.

We do still have copies of Fleming's manual. Send me a PM if you want to place an order.

[SVOfish]

I would like both of these books. Please PM me with more info.

[Meotchh]

I would like both of these books. Please PM me with more info.
At this time we are out of stock on Alan Slocum's manual & we do not have an eta on when we will receive more prints. We do have several copies of Mike Fleming's manual.
If you are interested in purchasing a copy of Fleming's manual, shot me a PM & I'll send you a PayPal invoice.

We will post an update when we have restocked with Slocum's manual.

[FoxBuddy]

We will post an update when we have restocked with Slocum's manual.

Looking forward to it. I'm new to this and I need to soak up all I can!

[Rlessary]

Any left?

[MikeFleming]

Whicn "any"? SVOCOP hat, Proud hat or manuals? I will check stock on Wednesday.

[Ford Builder]

I would like, Slocums Turbo hand book when they come available .

[Perce3]

I would like an Slocums Turbo book if and when available.

Thanks

Also where would somebody get a turbo rebuild?
I'm in Bellingham , WA

[Meotchh]

I'm checking on the status of Slocum's book. I hope to have an update by next week.

As for TC rebuilding, there is an outfit near Portland that a couple guys down there have used with some success., Otherwise, you can ship it to Charlie at Evergreen.

[Perce3]

I'm checking on the status of Slocum's book. I hope to have an update by next week.

As for TC rebuilding, there is an outfit near Portland that a couple guys down there have used with some success., Otherwise, you can ship it to Charlie at Evergreen.


Do you have a more detailed address for Charlie at evergreen?

Thanks for the help

Later

[Meotchh]

http://www.evergreenturbo.com/contact.html

[Perce3]

Thanks for info

[Patrick]

Well, I just got a call from Mr. MerkurEncyclopedia, Allan Slocum.

The books will be delivered this week, so you can request billing/payment info from Meotchh and we might be able get them in the mail early next week.

[Ford Builder]

KOOL ! Fast is good!

[Patrick]

Well, that didn't take very long!!! :) :runningdog:

[Meotchh]

Thank you everyone for your patience.

We now have a batch of 10 of Slocum's manual & a batch of 17 of Fleming's manual. I have sent PM's to each of you that have posted a request in this thread. Please respond to the PM with your paypal address & I will send out an invoice. If you are interested in apparel or additional manuals, these too can be combined in your order. Everything ships via USPS flat rate shipping in the US. If it fits it ships!

Thanks,
Mitch

[rodster]

PM sent...

[Meotchh]

Check you email Rodster! You should see an invoice.

[rodster]

Got it and payment sent! Thanks!

[rodster]

Arrived today. That was fast!


Great addition to the library! :like3:

Thanks.

[Meotchh]

Good deal! It's defintely a great addition. Thanks for the order Rodney.

[Meotchh]

We are running low again on the Slocum manuals. At this time we do not have an eta on a restocking of the manual. We are trying to have a batch ready for the Mustang 50th at LVMS (http://www.svocop.com/forum/showthread.php?2148-Mustang-50th-anniversary-at-LVMS-April-16-20-2014), but we cannot gaurantee we will have them at this time.

If you would like a manual now, please send me a PM with your request. I (the Treasurer) will send you an invoice via paypal for your order.

[Ford Builder]

Mine is on it's way.

[Ford Builder]

Well I just got mine today, Thanks Mitch now with the two manuals It should cover all I need to fix the beast if needed .

[FoxBuddy]

Well I just got mine today, Thanks Mitch now with the two manuals It should cover all I need to fix the beast if needed .

I forgot to mention I received mine before Christmas. Nice book!

[Meotchh]

Great! Thanks for the update guys. Looks like the avg shipping time to Canada is 10 business days. I hope you get some good use out of them!

[BLK BRD 88]

Mitch,
If you still have copies of both manuals will you PM me a price including shipping to 85022, & tell me where to send the pesos?
Thx
Ron

[Meotchh]

Hey Ron,

Check your PM box.

Mitch


Mitch,
If you still have copies of both manuals will you PM me a price including shipping to 85022, & tell me where to send the pesos?
Thx
Ron

[BLK BRD 88]

Thanks Mitch,
I checked it & replied....now, where do I watch for the invoice, on here or on my paypal account?
Ron

[MikeFleming]

The email addy associated with your paypal account.

[BLK BRD 88]

Bueno, I will keep an eye out for it to appear there.
Ron

[BLK BRD 88]

The manuals arrived yesterday and I am buried in reading (that I must admit is over my head), but I'm learning........!
Ron

[Meotchh]

Glad to hear that Ron! There will be a test next week.

[BLK BRD 88]

An "open book" test I presume!
Ron

[MikeFleming]

An "open book" test I presume! Yes, of course. But there is a time limit.

[David Eckel]

I would like to get a hold of one of these handbooks. I PM'ed the point of contact in the original post, but no response. Is there another link on how to order one of these?

[Raven855]

Did you PM Meotchh? or Patrick? It should be Meotch, I'll give him a heads up on the inquiry. I'm sure he will be with you soon.

[David Eckel]

Yes, it was Meotchh I PM'ed. Thanks for the response.

[Meotchh]

I'm back & I responded to David's request. I've been quite buried with work over the last 3 weeks.
Please be aware, we do not have any copies of the Alan Slocum manual in stock. We do still have copies of Fleming's manual.

[SVOfish]

Any of these left?