Search:

Type: Posts; User: SchoolBoy; Keyword(s):

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    10
    Views
    844

    Have you made any progress with creating the a/c...

    Have you made any progress with creating the a/c compressor bracket?
  2. This is my 85 Svo sitting 17" wheels. The konis,...

    This is my 85 Svo sitting 17" wheels. The konis, lower control arms and swaybar bushings are all relatively new 20-30k miles. Looks similar to your car I think.


    9906
  3. Replies
    7
    Views
    581

    Thank you for this link, the 1st one you posted...

    Thank you for this link, the 1st one you posted doesn't work for me.
  4. Replies
    7
    Views
    581

    Who's doing the rebuilds?

    Who's doing the rebuilds?
  5. Replies
    10
    Views
    630

    Hop on Facebook and check with steve schlodes for...

    Hop on Facebook and check with steve schlodes for a head, hes very reasonable.
  6. Replies
    6
    Views
    297

    The thing with the cometic gasket is it requires...

    The thing with the cometic gasket is it requires a surface finish that most shops can't actually give. Its a level of smoothness that can't be discermed by hand. It take an expensive scanner.
  7. Replies
    50
    Views
    4,338

    Your right, the compressor bracket will be the...

    Your right, the compressor bracket will be the tricky part. I have part numbers for almost everything else.
  8. Replies
    50
    Views
    4,338

    Mike was there a part number on the...

    Mike was there a part number on the accumulator/drier?
  9. Replies
    31
    Views
    2,160

    Going with an 8.8 this time?

    Going with an 8.8 this time?
  10. Replies
    50
    Views
    4,338

    The problem is not that if they work but for how...

    The problem is not that if they work but for how long. The deal is the HR980 wasn't ment for those pressures and its not rebuildable.
  11. Replies
    50
    Views
    4,338

    Mike I don't know what you'll run into with the...

    Mike I don't know what you'll run into with the belt conversion and tbird parts. However I was lucky enough to be in contact with the last guy to buy a hose wizards kit. The part numbers for items...
  12. Thread: Clutch noise

    by SchoolBoy
    Replies
    2
    Views
    434

    Bingo chalky had the aluminium flywheel and drive...

    Bingo chalky had the aluminium flywheel and drive shaft and it was noisy bugger.
  13. Replies
    3
    Views
    472

    Boports Baby Cams?

    I am currently running a freshly cut 86 spec svo cam from deltacams in my 85 svo and I love the street manners. But I'm curious if anyone has dyno sheets for the boport 1.1 & 1.5? I'm curious to...
  14. Replies
    25
    Views
    2,024

    Another catch can you can look at is the Tracy...

    Another catch can you can look at is the Tracy Lewis dual port Monster can. Theres 2 versions the sealed RX version or the signature can that can be opened and cleaned... The signature one is what...
  15. I have a NOS passenger headlight.

    I have a NOS passenger headlight.
  16. Thread: Windage tray

    by SchoolBoy
    Replies
    9
    Views
    674

    That's what I though on my last motor till we...

    That's what I though on my last motor till we realized the guy went to big on the piston to wall clearance.
  17. Replies
    29
    Views
    2,127

    All he lists on his site is that its 436"...

    All he lists on his site is that its 436" advertised lift.
  18. Replies
    29
    Views
    2,127

    Between the ranger roller you have now and the...

    Between the ranger roller you have now and the bo1.5. Basically do all your other changes such as the cam and exhaust manifold. Then dyno that set up with the ranger cam, then swap cams and repeat....
  19. Replies
    29
    Views
    2,127

    To bad its so damn expensive and time consuming...

    To bad its so damn expensive and time consuming but an A/B dyno test between the two cams would be interesting.
  20. Replies
    29
    Views
    2,127

    All of boports cams are rollers.

    All of boports cams are rollers.
  21. Replies
    24
    Views
    2,141

    Unfortunately he has passed away. Depending on...

    Unfortunately he has passed away. Depending on your access to tools you could piece one of these kits together. Hardest part will probably be fabing up the compressor mounting bracket.
  22. Replies
    62
    Views
    4,298

    Its possible that the coolant switch for the fan...

    Its possible that the coolant switch for the fan has gone bad, but keep in mind the stock one kicks the fan on at like 210*ish. You can always put a painless brand switch part number 30110 kicks the...
  23. Replies
    11
    Views
    551

    I asked the RonDavis sales rep when I bought mine...

    I asked the RonDavis sales rep when I bought mine and basically some racing rules don't allow them due to high probability of leaking.
  24. Replies
    62
    Views
    4,298

    No... Thats why I had to cut mine off order the...

    No... Thats why I had to cut mine off order the correct size and pay a local guy to weld them on. So your kinda back to checking summit for a 86-99ish ranger 2.3L radiator.
  25. For me if I was start over with another svo that...

    For me if I was start over with another svo that wasn't a 80k mile or less survivor.... I'd do these things: the 3g swap first; put the cooling fan on a relay to remove the load off the stock...
Results 1 to 25 of 172
Page 1 of 7 1 2 3 4