Search:

Type: Posts; User: Mike S; Keyword(s):

Page 1 of 9 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    4
    Views
    292

    The stock Konis won't work. You can use Konis...

    The stock Konis won't work. You can use Konis for the SN95 or the 87-93 GT. I ended up using the Adjustable Tokicos for the SN95. If I had to do it over again, I would get the Foxbody Tokicos as...
  2. Replies
    4
    Views
    292

    Roberto2000 was doing some machining of the ball...

    Roberto2000 was doing some machining of the ball joints as a side gig. He did mine. I went with the SN95 spindle so I upgraded to the Steeda x2 ball joints.
  3. Replies
    5
    Views
    260

    Sticky: Rest in peace Bob. May you see the face of God.

    Rest in peace Bob. May you see the face of God.
  4. Replies
    1
    Views
    105

    I think the top diagram will insure the same...

    I think the top diagram will insure the same pressure at all injectors. On a boosted application, it is important to not have a lean cylinder to avoid grenading the piston. Maybe someone has done...
  5. Replies
    23
    Views
    1,346

    For me, the best money spent on my suspension...

    For me, the best money spent on my suspension upgrades was first the MM subframe connectors, then the MM panhard bar and rear lower control arms. This helped to reduce the the understeer on the...
  6. Replies
    7
    Views
    360

    You can get one here:...

    You can get one here: https://www.jegs.com/i/JEGS/555/60640/10002/-1
  7. Thread: Hose ID

    by Mike S
    Replies
    5
    Views
    221

    There are 2 solenoids mounted on the back side of...

    There are 2 solenoids mounted on the back side of the PS shock tower. One is for the overboost buzzer and the other is the EGR control solenoid.
  8. Thread: EEC Wanted

    by Mike S
    Replies
    36
    Views
    1,790

    The small connector near the battery is part of...

    The small connector near the battery is part of the code reader connections.

    The ECM doesn't control the fan. The fan control sensor is located in the lower intake facing the firewall. The relay...
  9. Replies
    34
    Views
    3,606

    And you confirmed cam timing? If your belt...

    And you confirmed cam timing? If your belt slipped a tooth then it would impact cam timing, not ignition timing.
  10. Replies
    34
    Views
    3,606

    Did you verify your timing and pull codes?...

    Did you verify your timing and pull codes? Popping while cranking sounds like a timing issue. Maybe it jumped a tooth?

    Weak valve springs will also cause the car to stumble (break up). My Norcal...
  11. Replies
    1
    Views
    114

    Did you change the master cylinder as well? Do...

    Did you change the master cylinder as well? Do you have the stock brake booster? If not, which one?

    The way to test it is do the 35mph to 0 test until all 4 wheel lock about the same time. You...
  12. Replies
    1
    Views
    107

    Yes, this should go away as the rings seal the...

    Yes, this should go away as the rings seal the cylinders. You will always get some steam on initial warm up as the moisture in the oil vaporizes.

    Make sure you do the motor braking method on...
  13. Replies
    5
    Views
    143

    I think this is the one you want. ...

    I think this is the one you want.

    https://lmr.com/item/LRS-5059/mustang-transmission-crossmember-adjustable-8293
  14. Thread: AC questions

    by Mike S
    Replies
    4
    Views
    190

    You will need to add a little more fuel and...

    You will need to add a little more fuel and timing when the the AC turns on. The load from the fan and the AC both occur at the same time.
  15. Thread: Oil specs?

    by Mike S
    Replies
    3
    Views
    163

    10w-30 is what my manual says for a stock engine....

    10w-30 is what my manual says for a stock engine. Oil viscosity requirements are based on journal clearances. If your engine has a lot of miles, then you could go thicker.
  16. Replies
    16
    Views
    1,066

    Front Brakes Hawk 'Club Racing' Brake Pads...

    Front Brakes
    Hawk 'Club Racing' Brake Pads (HB125E.650)
    Blue 9012 Brake Pads

    Rear Brakes
    EBC Brake Pads - Yellowstuff 4000 Series (DP41161R)
    Yellowstuff 4000 Brake Pads
    Ultra High Friction...
  17. Replies
    6
    Views
    6,122

    When I had stock brakes, I used Hawk Blues on the...

    When I had stock brakes, I used Hawk Blues on the front and EBC yellows on the rear. Flush and fill your brake fluid with Motorcraft DOT3. It has the highest boiling point of any DOT 3 fluid...
  18. Sticky: I use 245/40 - 17s on 2005 -2010 GT Mustang rims.

    I use 245/40 - 17s on 2005 -2010 GT Mustang rims.
  19. Replies
    7
    Views
    780

    9887 Maybe this will help.

    9887

    Maybe this will help.
  20. Replies
    118
    Views
    10,466

    When you pull the fuel tank, don't forget to...

    When you pull the fuel tank, don't forget to check the filler neck grommet. It can leak from there on a 3/4 full tank.
  21. Replies
    2
    Views
    291

    I have one you can have $25 + shipping.

    I have one you can have $25 + shipping.
  22. Replies
    8
    Views
    697

    If you are still getting the ECT code with a new...

    If you are still getting the ECT code with a new one installed, then you have a wiring issue or a pin issue when you did the LA3 swap.
  23. Replies
    8
    Views
    697

    Have you removed and cleaned the VAM? If not,...

    Have you removed and cleaned the VAM? If not, give that a try. Are you getting any smoke out of the exhaust when driving? If so, what's the color?

    Did you pull the codes again to confirm the...
  24. Replies
    33
    Views
    3,991

    Did you replace the PIP when you replaced the...

    Did you replace the PIP when you replaced the TFI? Is the TFI rotated where it is close the the lower intake?

    You may need to perform the wiggle test on your harness once you get it running again...
  25. Thread: Low Engine Temp

    by Mike S
    Replies
    4
    Views
    579

    I don't know the thermodynamics of why the system...

    I don't know the thermodynamics of why the system will run cooler if not pressurized, but from my personal experience that is what happens until such time as you loose to much fluid for the system to...
Results 1 to 25 of 221
Page 1 of 9 1 2 3 4