Search:

Type: Posts; User: vrinner; Keyword(s):

Page 1 of 9 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    1
    Views
    132

    Fuel injector connector wire

    So whats the best way to connect a wire to the injector adapter. Not sure if they sell something specific.

    This is Ford part number M-14464-U2J
    8944
  2. Replies
    74
    Views
    4,816

    That is just damn sexy!

    That is just damn sexy!
  3. Thread: PCV Explained?

    by vrinner
    Replies
    20
    Views
    912

    OK...so after reading all of this I am for sure...

    OK...so after reading all of this I am for sure in need of changing my setup.

    I have a Peterson catch can setup. The valve cover goes to the catch can, then the catch can goes to the PCV/block....
  4. Replies
    59
    Views
    2,973

    OK...just to make sure, like my option 1 picture...

    OK...just to make sure, like my option 1 picture in previous post? Also make sure valve is pointing towards the cross over inlet pipe...do you mean the valve inside the wastegate or something else....
  5. Replies
    59
    Views
    2,973

    External Wastegate Manual Boost Control question

    OK...so I've seen a couple of different versions of this.
    Option 1
    Boost hose from turbo compressor to the inlet (bottom) of the Gillis Valve
    Hose from outlet (side) of the Gillis Valve to the...
  6. Replies
    59
    Views
    2,973

    Setup to drain back into the pan...kind of. So...

    Setup to drain back into the pan...kind of. So from the valve cover it goes into the can. There is another larger line that goes to the block on the intake side where where the stock pcv valve is....
  7. Replies
    59
    Views
    2,973

    Yeah...the plug wires do have a grommet and the...

    Yeah...the plug wires do have a grommet and the other line needs it for sure
  8. Replies
    59
    Views
    2,973

    A little bit further along. Had to have a new...

    A little bit further along. Had to have a new turbo oil feed line and drain made. Next is put on the heat shielding (thanks Gregg!) then button up the small bits.
    8864
    8865
    8866
    8867
  9. Replies
    59
    Views
    2,973

    Thanks Greg. PM sent. It certainly has taken...

    Thanks Greg. PM sent.

    It certainly has taken some time to get things all worked out. Everything else on the car is setup great. Just gotta get the motor done.
  10. Replies
    2
    Views
    166

    Stainless steel pipe

    Anyone know of a place to get stainless steel pipe. Specifically used for coolant lines? Need to make something for a special application. it's either that or hack up the stock stuff and just use...
  11. Replies
    10
    Views
    527

    Fabulous Fords Forever 2016

    The 31st Annual FABULOUS FORDS FOREVER car show is Sunday, April 17th, 2016 at Knott's Berry Farm in lovely Buena Park, CA.

    My wife Diana and I will host our annual get together/BBQ at our new...
  12. Replies
    59
    Views
    2,973

    Heat shields...yes...in progress Next Track...

    Heat shields...yes...in progress
    Next Track day...Hopefully late April at Spring Mountain
    Red...of course
    Supports...HO Fibertrend hood. The supports have been "modified" many times. Throttle...
  13. Replies
    59
    Views
    2,973

    Already had to cut out some of the fiberglass...

    Already had to cut out some of the fiberglass hood support material to clear the turbo. Seems to close OK right now but we will see once it's all put together and running.
  14. Replies
    59
    Views
    2,973

    2.6 motor installed. Exhaust manifold flipped...

    2.6 motor installed. Exhaust manifold flipped over using some "Chip Flips"
    8736
    8737

    Cut and rotated the upper intake.
    8734
    8735


    I little more plumbing left to do then back to the dyno...
  15. Best coolant/anti-freeze for occasional driver

    Looking for the best/recommended coolant/anti-freeze for an occasional driver car.
  16. Replies
    8
    Views
    653

    Yea...that looks correct. I'm assuming I use...

    Yea...that looks correct.

    I'm assuming I use the same alternator upper braket
  17. Replies
    8
    Views
    653

    I was looking for the power steering pump bracket...

    I was looking for the power steering pump bracket for a serpentine setup with the tensioner and stuff. Local junk yards no such luck and I need to get the car done. I was going to keep the Stinger...
  18. Replies
    8
    Views
    653

    Well, I couldn't find (easily) a bracket for the...

    Well, I couldn't find (easily) a bracket for the serpentine pulley setup so now I've got to install my Esslingler pulley setup...which because I've modded the pulleys for the missing tooth gear, I'm...
  19. Replies
    31
    Views
    1,663

    I'd like to get a head count for Saturday. Also...

    I'd like to get a head count for Saturday. Also if we are thinking about attempting K1. I'll see what I can do to make a reservation. Last time I was there with my kids...they had to stop the race...
  20. Replies
    31
    Views
    1,663

    We do have a fold out sleeper sofa that really is...

    We do have a fold out sleeper sofa that really is pretty comfortable. If someone needs a place to stay it's first come first served. Just let me know.
  21. Replies
    31
    Views
    1,663

    I think Mitch got a house deal. Not sure if there...

    I think Mitch got a house deal. Not sure if there is a hotel deal. I do have a fold out bed...it's actually very comfy!
  22. Replies
    19
    Views
    750

    OK...now someone is just showing off! Nice!

    OK...now someone is just showing off! Nice!
  23. Replies
    19
    Views
    750

    So is the dipstick tube supposed to be loose?...

    So is the dipstick tube supposed to be loose? Mine just kind of plops in there. Use any sort of sealant?
  24. Replies
    8
    Views
    653

    Megasquirt or Stinger EMS

    OK...so I'm just about to the point of wiring the racecar back up. I have the Stinger 4424 V4 EMS and what appears to be most of the wiring harness out of the old car.

    The racecar still has the MS...
  25. Replies
    1
    Views
    190

    WTB: Serpentine pullies

    Need the alternator and power steering pump serpentine pulleys. Anyone or know where to get them other than junk yard.
Results 1 to 25 of 220
Page 1 of 9 1 2 3 4