Search:

Type: Posts; User: Unclesams_SVO; Keyword(s):

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    105

    Fuel system question

    I am completely redoing the fuel system in my car and updating everything to 6an lines. I am doing a full wire tuck as well so I want to keep the engine bay as clean as possible.

    My question is...
  2. Replies
    177
    Views
    19,105

    To get the new brake booster in required some...

    To get the new brake booster in required some drilling and the use of a BFH to massage the car into giving up the space for the lager booster. Unfortunately some of the pretty engine bay paint is not...
  3. Replies
    177
    Views
    19,105

    I know I have been quiet lately (I have been...

    I know I have been quiet lately (I have been traveling for work a lot this year) but I got some parts and motivation this weekend so with out further delay......

    Last time I drove the car there...
  4. Replies
    177
    Views
    19,105

    My next step is wiring, I will admit that I am a...

    My next step is wiring, I will admit that I am a little intimated by this with everything that I want to install:

    - Flex fuel sensor
    - Boost controller
    - Wideband
    - Coil packs with harness
    -...
  5. Replies
    177
    Views
    19,105

    I decided to mount the coil packs in the...

    I decided to mount the coil packs in the firewall. I made a plate that secures to the studs that hold the heater assembly. The brackets are ICT and fit the coil packs very well. I still need to make...
  6. Replies
    177
    Views
    19,105

    I then went to install my new water neck and...

    I then went to install my new water neck and adapter that I made and found out it interferes with the water pump pulley. Since I did not need the pulley for the power steer pump.......out came the...
  7. Replies
    177
    Views
    19,105

    I went to install the Esslinger water pump but...

    I went to install the Esslinger water pump but the pulley did not line up. So after contacting them and finding out that the bully flange is only pressed on and that I could fix that on my own. This...
  8. Replies
    177
    Views
    19,105

    I have plugging away still, just slacking on...

    I have plugging away still, just slacking on updates.

    Mocked up the I/C plumbing and had to shorten the boot going to the new upper plenum so it would clear the strut bar. I also installed the...
  9. Replies
    177
    Views
    19,105

    Test fitting more stuff. ...

    Test fitting more stuff.

    http://vb.foureyedpride.com/attachment.php?attachmentid=136296&d=1633834222
  10. Replies
    177
    Views
    19,105

    Exhaust mock up time. Gnari manifold Gnari...

    Exhaust mock up time.


    Gnari manifold
    Gnari waste gate down pipe,
    Tail 38mm waste gate
    ARP bolts


    I need to smooth out the bolt holes in the manifold as they are catching the bolts and...
  11. Replies
    177
    Views
    19,105

    I will make sure to do that, thank you for the...

    I will make sure to do that, thank you for the idea.
  12. Replies
    177
    Views
    19,105

    The head is installed this weekend and found true...

    The head is installed this weekend and found true TDC so I can adjust my timing pointer.

    It is nice to see the engine as a long block, unfortunately I am still waiting on 2 more panels from Scott...
  13. Replies
    1
    Views
    186

    interesting, I ended up deleting the entire...

    interesting, I ended up deleting the entire factory style engine mount and went with a modern style poly puck mount. https://tbirdcougarparts.com/#!/ not cheap but they are adjustable and well made.
  14. Replies
    2
    Views
    172

    got any pictures or a diagram of the boost...

    got any pictures or a diagram of the boost controller in question?
  15. Replies
    7
    Views
    338

    yes I am i stalling a Ron Francis harness in my...

    yes I am i stalling a Ron Francis harness in my car (the Pimp harness version). Not 100% plug n play but A good quality harness.
  16. Replies
    177
    Views
    19,105

    I also started to reroute the body harness to...

    I also started to reroute the body harness to tuck it behind the fenders, looks like I will only have to extend a couple wires which was a surprise to me. Once everything is laid out and extended I...
  17. Replies
    177
    Views
    19,105

    I finally installed the Scott Rod aluminum panels...

    I finally installed the Scott Rod aluminum panels this weekend (for some reason I was psyching myself out over these), they went in fairly easy with some trimming here and there. I must say using...
  18. Replies
    177
    Views
    19,105

    I installed a Mach 1 chin spoiler today, this is...

    I installed a Mach 1 chin spoiler today, this is something I have been wanting to do for a while and I am happy with the results.

    10145

    10146

    I had to use a heat gun and use masking tape to...
  19. Replies
    177
    Views
    19,105

    Today I tacked replacing the valve train (I...

    Today I tacked replacing the valve train (I previously changed the valve seals out to I left those alone). On a side note the Esslinger rocker removal tool did not work with roller rockers from...
  20. Replies
    177
    Views
    19,105

    With installing a new radiator I needed to come...

    With installing a new radiator I needed to come up with another way to mount my Ford Contour electric fan. I decided to make my own mount since the pre made option available is more then I wanted to...
  21. Replies
    177
    Views
    19,105

    Being in the Southwest I wanted as much cooling...

    Being in the Southwest I wanted as much cooling as possible. :cool:
  22. Replies
    177
    Views
    19,105

    I started mocking up my new radiator this...

    I started mocking up my new radiator this weekend, it is a Mishimoto down flow (I wanted to reduce the amount of radiator hose length).
    P/N Mishimoto MMRAD-MUS-79DP

    Since my car has had a couple...
  23. Replies
    177
    Views
    19,105

    I started to install the Stifflers transmission...

    I started to install the Stifflers transmission cross member and Spyder kit. When looking at the cross member position per the instructions I may have to decide to keep the stock WC T-5 or upgrade to...
  24. Replies
    177
    Views
    19,105

    So this next part was more of an "oh wow, I did...

    So this next part was more of an "oh wow, I did not even know these existed" kinda thing. I am pretty sure I saw these on a thread on this forum and said, yep I need those.

    When I installed my...
  25. Replies
    177
    Views
    19,105

    I gave the primer a few days to fully harden...

    I gave the primer a few days to fully harden before I laid the silver paint down.

    http://vb.foureyedpride.com/attachment.php?attachmentid=135973&d=1628087006
    ...
Results 1 to 25 of 159
Page 1 of 7 1 2 3 4