Intercooler to throttle body clamps from Summit racing :Vibrant Performance #2791 and #2793
Type: Posts; User: Under Pressure; Keyword(s):
Intercooler to throttle body clamps from Summit racing :Vibrant Performance #2791 and #2793
I got tired of the hood prop so I added MRT no drill hood struts, works great.10164
Esslinger.com intermidiate shaft $337.70 last forever!
Pure Gas.org. Just say No to ethanol! Many stations here sell non-ethanol gas. I got 8 gal. pure gas today at Valero $4.29. Better for everything fuel tank to combustion! More Power Scotty!
My motor sopped working and I tapped it and it started working. It did it again last week. I tapped it again and it started working. I bought a new motor, I don't want to have to keep removing the...
The relay for my fan crapped out and my radiator blew the seam out on the plastic side chamber. I ordered a all aluminum one from American Muscle and a new relay from Summit Racing.
I needed to replace my lower radiator hose. All the places were showing hoses for the V-ate. My old hose still had the tag on it. Goodyear changed their hose division name to Continental Elite. Hose...
I had the 90* water hose that comes out of the oil cooler to the heater core burst. While removing the small hose from the lower manifold the nipple on the hard line broke from rust. I brought it to...
I have the boost control solenoid plugged in just don't have hoses connected. If I connect my timing light will I see 6* added to the base 10 with the spout out?
I contacted Ron Francis about the Premium switch, here's their reply " we do not support the octane switch. Our system has it run on the premium fuel table.
Ok thanks, I have a threaded rod on my wastegate adjusted to 15lb and not using the boost control solenoid. Even though the premium switch light is not on I'm still in the premium setting in the EEC?...
The vam e4zx B529-AA will work on al 5 speed 2.3 sohc turbos as will a E9xx 12 b529-AA
Mike are all 84-86 SVO VAM's calibrated the same and inter-changeable with different SVO computers? Are SVO computers pinned the same at the 60 pin connection? What pin number goes to the premium...
Thanks Mike from what I've been reading I think mine is a piece. I put about 30 miles on the car yesterday. Now that it is running better than it ever has, my seal might not bee bad. It runs so...
Got my car back from RJ Performane this morning with my new Ron Francis wiring harness. Starts right up and runs great. To celebrate I put in 6 gal. of 90 octane non ethanol in her, she likes it. woo...
I got a early birthday present today. My mechanic Kevin at RJ Performance called this morning and said my car was ready. It starts right up now and runs great. The Ron Francis harness was only the...
Ford changed the 2 piece rear main engine seal to a one piece. Can you replace a 2 piece seal with the one piece? Has anybody replaced the seal with the engine in the car? Are the flywheel bolts...
I talked it over with my mechanic about the wiring and decided to have him install the Ron Francis engine harness. He's installed them in other vehicles and said they are very high quality. Ron...
I haven't bought it yet, my mechanic has been busy. I want him to look at the mess in there now and see if he can work with it as is. If he says no go I'll get the harness. I'm concerned about...
I'm having my engine wiring repaired. I have a 85 that I've up graded to a 86. I want to use the Ron Francis Harness. The web site says for 87-88 Turbo. I changed my alternator to the internal...
I've changed too many blown head gaskets. This last time I went with a very expensive copper head gasket. You can take a Dremel and clean up the cast flashing on the intake ports, clean it leave a...
That looks and sounds like a fun project. It'll be a sweet ride!
i'M Looking at the Ron Francis harness. Is that the one you used?
Did you rewire the car? Did you pull the engine to install the harness. I want to install a new harness in my 85. Would like to not have to pull the engine.
Yes it's still there, they have a big sale on everything.