Search:

Type: Posts; User: MikeFleming; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    7
    Views
    19

    On, Wayne!!

    On, Wayne!!
  2. Replies
    7
    Views
    19

    Maybe start with just a couple PSI - until the...

    Maybe start with just a couple PSI - until the size of the leak is ID'd. Keep in mind that leaks will put sticky coolant all over. Rinse with lots of water from garden hose. Observe local laws as...
  3. If it goes into gear with engine off, and not...

    If it goes into gear with engine off, and not with engine running and clutch depressed, most likely the disk is installed backwards, or something is fouling the disk to the pressure plate. Hate to...
  4. Replies
    7
    Views
    19

    I would inspect all the coolant tubes. They are...

    I would inspect all the coolant tubes. They are well known to have rust issues after a couple decades. There's two that run around the rear of the head, near the EGR tube.
  5. Replies
    4
    Views
    36

    85.5/86? Left (drivers) side in the oil pan.

    85.5/86?

    Left (drivers) side in the oil pan.
  6. Replies
    3
    Views
    24

    Welcome home, BTW!!

    Welcome home, BTW!!
  7. Replies
    3
    Views
    24

    IIRC the two that go under the main arm rest are...

    IIRC the two that go under the main arm rest are hex heads, the one on the forward part of the armrest (above the hand grip) is a Phillips. I wonder if LMR has those listed as spares? may have some...
  8. Replies
    4
    Views
    36

    Looks like the oil level sensor in the sump....

    Looks like the oil level sensor in the sump. That's about the only single-wire there besides the 1984/85 coolant temp fan switch, the oil pressure sensor and the coolant temp sensor on the back of...
  9. Replies
    1
    Views
    19

    Presure sensor - Yes, those are tepered pipe...

    Presure sensor - Yes, those are tepered pipe threads.

    The turbo oil feed line does NOT use pipe threads - the seal is made at the double-flare taper between the tube end the the fitting, NOT on...
  10. Replies
    5
    Views
    44

    Tack the tubes in place - very little heat. Then...

    Tack the tubes in place - very little heat. Then remove the cross member assembly and full-circle weld them on hte bench without the bushings installed.

    Curious that it's bright CAD plated when...
  11. Replies
    5
    Views
    44

    Even twenty years back, the only place I knew of...

    Even twenty years back, the only place I knew of to get replacement bushings for the cross member was to buy the Ford Performace unit and swap the bushings and center tube to your old one. ...
  12. Replies
    9
    Views
    791

    Welcome aboard. VERY nice car. Coming will all...

    Welcome aboard. VERY nice car. Coming will all 30+ years of service history is a find for sure.

    There are several other members here that also have low mileage 86 models. We should form a club.
  13. OUCH!!

    OUCH!!
  14. Replies
    12
    Views
    141

    Compression Check Spark - Verify this Fuel -...

    Compression Check
    Spark - Verify this
    Fuel - what was fuel pressure at 3500 RPM, free-revving?
    Difficult to believe that fuel would be limited when free-revving since it';s not using much fuel...
  15. Replies
    2
    Views
    59

    84-earlu 85 has non-coolant-fed turbo; late-85-86...

    84-earlu 85 has non-coolant-fed turbo; late-85-86 has coolant-fed turbo. Different tubes.

    Which do you need? The later ones all stay above the exhaust manifold.
  16. Replies
    2
    Views
    62

    You are obviously a glutton for punishment and...

    You are obviously a glutton for punishment and have come to the right place among like-minded folks.

    Keep us posted.
  17. Replies
    1
    Views
    302

    Welcome aboard to a fellow SHO owner. Help...

    Welcome aboard to a fellow SHO owner.

    Help yourself to the beer in Pat's fridge (the one with all the stickers on it). The other one has soda. Feel free to any of that too.
  18. Replies
    4
    Views
    271

    Can't tell from the pic - is it a coolant-fed...

    Can't tell from the pic - is it a coolant-fed CHRA?
  19. Some Old SVO Videos and Advertisements

    https://lmr.com/products/mustang-svo-history

    After the first one (link above), there are many more when that one completes.
  20. Replies
    5
    Views
    90

    Only in weight. Otherwise same functionality.

    Only in weight. Otherwise same functionality.
  21. It is a stock mount header made by a fellow named...

    It is a stock mount header made by a fellow named Rod of Rods Headers. IIRC he was sommers in Canada. He passed away a few years back. Big Sigh.
  22. I don't see chatter and pictures from this event...

    I don't see chatter and pictures from this event yet. Where's my Ban Hammer??
  23. "The womb" doesn't usually have neck-snapping...

    "The womb" doesn't usually have neck-snapping g-forces that we often see in motor vehicles.
  24. Get those kids some neck supports.

    Get those kids some neck supports.
  25. Thread: Helmets

    by MikeFleming
    Replies
    15
    Views
    199

    It's always a good idea to use long sleeve shirts...

    It's always a good idea to use long sleeve shirts (cotton or wool - NO SYNTHETICS), long pants (cotton / wool), & closed-toe shoes (no sandals or slippers).
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4