PDA

View Full Version : Engine


Pages : 1 2 [3]
  1. Do all turbo heads crack?
  2. Stainless steel pipe
  3. Thermostat Gasket?
  4. Re-assembling the intercooler
  5. EGR operation questions
  6. How to clean valves?
  7. Cam search
  8. What caused this?
  9. External Fuel Pump
  10. Driveshaft yoke part number
  11. No Boost... Help?
  12. Torque
  13. Autolite 104 vs 764 plugs
  14. Need a new Transmission Input Shaft
  15. New water temp gauge
  16. Heli-Coils in Exhaust Manifold
  17. stock wastage spring pressure?
  18. Engine idle bouncing
  19. Timing belt one tooth off!
  20. PLUGS
  21. Crankcase Separator Clogged? (Oil-Out-The-Dipstick)
  22. Stinky boost?
  23. 79 cylinder head
  24. Seeking Engine Rebuild Advice...
  25. Just installed new flywheel, clutch- ow no clutch. WTH?
  26. A/c print sizes
  27. Flywheel
  28. IC brackets
  29. Stock Oil Pressure?
  30. Just a test...
  31. New flywheel or re-surface ?
  32. Valve Seals
  33. Water Pump Part #?
  34. Upper Intake nuts, bolts, studs
  35. Vacuum leak?
  36. ac replacement
  37. Fuel Tank Filler Pipe Grommet
  38. Fan Mail
  39. Egg smell on initial start
  40. Distributor replacement-my approach and experience
  41. V Belt part numbers
  42. Low RPM detonation
  43. cam followers
  44. Need some help with DTCs
  45. No Fuel Pressure
  46. Valvetrain noise
  47. Changing lifters
  48. MAF Conversion
  49. Valve stem seals - dumb ?
  50. Header repair and ceramic coating
  51. Any interest in New 84 TailPipes and maybe the muffler
  52. Stock Intercooler Composition
  53. Blow-off Valve Recommendations
  54. Loss of oil pressure
  55. Lumpy idle
  56. Intercooler upgrade question
  57. Premium Switch
  58. V-belt question
  59. Radiator suggestion
  60. Conquest / Starion intercooler swap
  61. Running Rough
  62. Shifter?
  63. Turbo and manifold upgrade
  64. Windage tray
  65. Thoughts/recommendations on intake porting / manifold-turbo coating??
  66. SS coolant lines
  67. New cam, new problem
  68. Clutch cable and quadrant
  69. Water pump....
  70. E85 boost levels
  71. Rear Main Oil Seal
  72. Clutch and flywheel....
  73. Boports Baby Cams?
  74. 1986 SVO Dies on Start-up When Cold
  75. Engine hard starting
  76. Clutch noise
  77. Distributer gear question
  78. Low Engine Temp
  79. Air Intake
  80. Replacement Exhaust
  81. Timing, ECT, or ?
  82. Stainless Steel Water Pipes 1985-1/2 SVO
  83. How in the holy hell....
  84. Coolant overflow
  85. oil to watercooled turbo
  86. Aluminum Head
  87. Cooling fan motor disassembly
  88. Adding an IC to non-SVO?
  89. Idle air by-pass solenoid gasket
  90. Piston Choices
  91. Head studs and head gasket
  92. EGR Tubes
  93. Which Fuel Sender?
  94. Oil specs?
  95. Coolant sensor location
  96. Limitations of stock internal wastegate / flapper...?
  97. Anyone heard from Boport?
  98. Shifter bushing
  99. AC questions
  100. HELP, engine breaks up under boost
  101. Cylinder Heads International - Stay Away
  102. Engine Coolant Temperature (ECT) Sensor readings
  103. Top Dead Center
  104. Trans cross member
  105. Thread tape on oil lines?
  106. Replacing the VAM-to-turbo inlet hose
  107. Coolant leak
  108. Cannot get transmission into gear Help Please
  109. Excessive smoke from catch can
  110. Starting to come together, finally :)
  111. Hose ID
  112. Stock T3 impeller sizes...?
  113. Engine Dampers
  114. PCV turbo inlet fitting
  115. Throttle body rebuild?
  116. Testing the VAM
  117. New turbo question....
  118. What belts go on?
  119. Turbo RPM Sensor
  120. Transmission fluid
  121. Catastrophe
  122. Broken turbo support bracket
  123. PCV Hose
  124. Rear Engine seal replacement
  125. Fuel system question
  126. Loud Squeaky Clutch Action
  127. Unleaded/Premium mode test
  128. Valve train geometry
  129. Engine will not run
  130. AC Components
  131. Stainless 3" downpipe options/sources?
  132. 3D Printed Manifold
  133. 3D printed throttle bracket