- Manual Boost Control Advantage (8 replies)
- Honey-Who?? (4 replies)
- Head Rebuild Options (3 replies)
- Oil cooler O-rings (15 replies)
- 36# Injectors (2 replies)
- Vacuum lines on the turbo (107 replies)
- Forced Induction or Mosquito Fogging or How to Diispose of Waste Oil (2 replies)
- Stiff Wastegate (1 replies)
- Roller cam v slider cam, different metallurgy? (1 replies)
- Boost Solenoid (0 replies)
- ebay intercooler (13 replies)
- Oil dipstick length? (6 replies)
- Valve Cover Oil Separator Install (1 replies)
- Turbo Oil Feed "Restriction"? (1 replies)
- Timing mark decals (3 replies)
- No Turbo Whistle at all and no turbo boost over 9psi???? (12 replies)
- ASTM A193 B6 Turbo Elbow Bolts? (5 replies)
- 5.0 throttle body question (2 replies)
- Oil Leak (9 replies)
- TPS and Ethanol (5 replies)
- Engine stall at 3000 RPM (17 replies)
- Help with Clutch Cable Adjuster (14 replies)
- Cold Air Intake Options (5 replies)
- Advice on best oil to use (8 replies)
- Replacement vam to turbo hose (0 replies)
- Whoah Pony! (Or, Halloween ain't over yet) (3 replies)
- Oil cooler wrench size? (5 replies)
- Fuel pump (1 replies)
- Fuel pump doesn't turn on (12 replies)
- Exhaust Upgrade Advise (5 replies)
- AEM 320LPH In-Tank Fuel Pump Kit (0 replies)
- Boost Leak!? (8 replies)
- Turbo oil line fitting (7 replies)
- 85 4e not going anywhere... (1 replies)
- bov? probly been asked a milion times (2 replies)
- Front Mount Intercooler (9 replies)
- 1984 SVO stock boost control system not working (34 replies)
- Power Steering Pump Pulley (1 replies)
- VAM stock hose replacement (4 replies)
- missing very bad below 3000 rpm (43 replies)
- t-5 fluid (14 replies)
- Oil Leak (15 replies)
- Engine spins but does not fire (20 replies)
- Crankshaft key pics (4 replies)
- The 87 SVO (17 replies)
- DIY Oil Separator or Catch Can, or let it burn? (14 replies)
- Replacement Coolant Hose (4 replies)
- Oil cooler channel blocked? (6 replies)
- Detonation, surging...EGR ? (12 replies)
- Smoking (10 replies)
- Let talk 2.5L motors (13 replies)
- Anyone running a center mount header? (13 replies)
- Intercooler question (9 replies)
- Merkur 90' oil filter (8 replies)
- Turbo to valve cover air vent line doesn't fit (20 replies)
- Who makes a good downpipe? (3 replies)
- vacuum or cooling? (12 replies)
- Turbo head crack prone areas? (1 replies)
- vacuum lines to bcs (5 replies)
- BCS and adjustable wastegate questions (15 replies)
- This is getting ridiculous (14 replies)
- 94-95 throttle body (2 replies)
- Replacement AC accumulator (11 replies)
- Turbo replacement decisions... (3 replies)
- E6 Manifold (2 replies)
- Does this belong here? (2 replies)
- Low Vacuum (8 replies)
- Small Journal Rebuild (9 replies)
- T3/T4 Question. (10 replies)
- Essy Round tooth kit (5 replies)
- She spins...she fires...she dies! (6 replies)
- exhaust wrapping a cast iron header (4 replies)
- One piece oil pan gasket (4 replies)
- Exhaust manifold studs (24 replies)
- Looking for ideas on how to build this 2.3 for my 84 svo (8 replies)
- injector size and fuel pump question (4 replies)
- Fuel System Issue (10 replies)
- Rings (19 replies)
- Turbo falling flat on its face (11 replies)
- cast iron exhaust manifold porting (3 replies)
- Engine noise, gear drive ??? (4 replies)
- 90* Intake Plenum (8 replies)
- cooling fan motor (12 replies)
- Measuring Cylinder Bores-A bunch of questions and some pics (15 replies)
- part #'s coolant hoses (16 replies)
- Main Bearing Ford Part Numbers (7 replies)
- Crankshaft Gear Removal (4 replies)
- whats the best coolant temp. (3 replies)
- Esslinger adjustable cam gear bolt torque. (3 replies)
- Garrett Oil Only CHRA (4 replies)
- SVO on e85 (20 replies)
- What Would Bolo Do? Typically LONG post (11 replies)
- AWD 97 Aerostar driveshaft (2 replies)
- Stock Air Box Mod (8 replies)
- Driveshaft question (5 replies)
- Look what showed up in my truck! (5 replies)
- oil cooler gasket (1 replies)
- 86 SVO overboosting (62 replies)
- Plastic Fuel lines (2 replies)
- coil on plug (16 replies)
- New Cam Install Questions (20 replies)
- Full 3" single exhaust with custom tail pipe (5 replies)
- Thrust spec for aux shaft? (8 replies)
- 2V vs. 4V??? (4 replies)
- Adjustable clutch cable (9 replies)
- Injector questions (11 replies)
- T3/T4 A/R Ratio (18 replies)
- Glowing Turbo and Manifold (18 replies)
- SN95 Throttle Body upgrade (9 replies)
- 2.3 crank VS 2.5 crank info (3 replies)
- Air/Oil Separator? (7 replies)
- Drilling head for 86 intake manifold (8 replies)
- Clutch recommendations? (36 replies)
- Boost Issue (17 replies)
- interchange intakes (11 replies)
- EGR pipe removal (9 replies)
- It figures..... (10 replies)
- BPV- which way? (7 replies)
- Idle question but not the same old. (18 replies)
- The muffler discussion, here, only here. (55 replies)
- Fuel system question (45 replies)
- How to Choose the Right Spark Plug??? (13 replies)
- Higher Compression Ratio (8 replies)
- Turbo Torque Specs (3 replies)
- Turbo Oil Feed Line copper washers (5 replies)
- Stud/Nut vs. bolt (19 replies)
- Pat was right !!!! (3 replies)
- Vacuum question (3 replies)
- Exhaust question (11 replies)
- Frozen nuts and bolts (1 replies)
- Valve Cover Differences (2 replies)
- PCV Explained? (20 replies)
- Turbocharger Video (2 replies)